View YB15CKW01-6F-JB_7444263.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

series yb short body pushbuttons www.nkk.com d100 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles general specifcations electrical capacity (resistive load) power level (silver): 3a @ 125v ac or 3a @ 250v ac or 3a @ 30v dc logic level (gold): 0.4va maximum @ 28v ac/dc maximum (applicable range 0.1ma ~ 0.1a @ 20mv ~ 28v) note: find additional explanation of operating range in supplement section. other ratings contact resistance: 50 milliohms maximum for silver; 100 milliohms maximum for gold insulation resistance: 200 megohms minimum @ 500v dc dielectric strength: 1,000v ac minimum between contacts for 1 minute minimum; 1,500v ac minimum between contacts & case for 1 minute minimum mechanical life: 1,000,000 operations minimum for momentary circuit 200,000 operations minimum for maintained circuit electrical life: 100,000 operations minimum nominal operating force: single pole: 1.47n for nonsealed; 1.67n for sealed double pole: 2.75n for nonsealed; 2.94n for sealed contact timing: nonshorting (break-before-make) travel: pretravel .059 (1.5mm); overtravel .059 (1.5mm); total travel .118 (3.0mm) materials & finishes housing/bezel: glass fber reinforced polyamide (ul94v-0) snap-in frame: stainless steel base: diallyl phthalate resin (ul94v-0) movable contactor: phosphor bronze with silver or gold plating movable contacts: silver alloy with silver plating or brass with gold plating stationary contacts: silver alloy or copper with gold plating switch terminals: phosphor bronze with tin plating lamp terminals: phosphor bronze with tin plating environmental data operating temperature range: C25c through +50c (C13f through +122f) for illuminated C25c through +70c (C13f through +158f) for nonilluminated humidity: 90 ~ 95% humidity for 96 hours @ 40c (104f) vibration: 10 ~ 55hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours shock: 50g (490m/s 2 ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) sealing: ip65 of iec60529 standard for panel seal models installation mounting torque: 0.785nm (6.95 lb ? in) maximum quick connect force: 24.5n maximum downward force on connector soldering time & temperature: manual soldering: see profle a in supplement section. standards & certifications flammability standards: ul94v-0 housing & base ul: file no. e44145 - recognized only when ordered with marking on switch. add /u or /cul before frst dash in part number to order ul recognized switch. all solder lug models recognized at 3a @ 125/250v ac or 0.4va @ 28v ac/dc maximum. csa: file no. 023535_0_000 - certifed only when ordered with marking on switch. add /c before frst dash in part number to order csa certifed switch. all solder lug models certifed at 3a @ 125/250v ac or 0.4va @ 28v ac/dc maximum.
series yb short body pushbuttons www.nkk.com d101 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt distinctive characteristics full face or spot illumination with incandescent lamps or multi-element leds, with or without resistors. choice of super bright leds in white, green, and blue as well as bright leds in red, amber, and green. combination bezel-barrier is an integral part of the switch and prevents accidental actuation. unique thermoplastic elastomer seal inside caps plus rolled sleeve of nitrile butadiene rubber at joining of housing and inner case, all for added protection to interior mechanism. dust and oil tight as well as splashproof panel seal models qualify to ip65 of iec60529 standards (similar to nema 4 and 13). panel seal models provided with exterior o-ring. distinctive design of snap-action contacts for shock resistance, long life, and sensitive actuation. high density design to give behind panel depth of less than one inch. terminals are epoxy sealed to lock out fux, dust, solvents, and other contaminants. latchdown for indication of circuit status, plus audible, tactile feedback with smooth, responsive operation. matching indicators available. actual size
housing k black only shapes bushing mounting s square c round r rectangular snap-in mounting k square m round n rectangular poles 1 spdt 2 dpdt 1 c k 01 yb led cap with clear lens and white insert without panel seal silver contacts with 3 amp rating solder lug/.110 (2.8mm) quick connect terminals green, super bright led round with bushing mounting black housing spdt on-(on) circuit circuits 5 on (on) ( ) = momentary 6 on on alternate action with latchdown contact materials & ratings w silver rated 3a @ 125v ac g gold rated 0.4va max. @ 28v ac/dc max. 5 description for typical ordering example YB15CKW01-6F-JB lamps typical switch ordering example 6 f solid cap: lens/insert colors bb white/white cb red/white eb yellow/white fb green/white gb blue/white incandescent lamp 05 5-volt 12 12-volt no code nonilluminated jb cap types & colors led cap: lens/insert colors jb clear/white super bright led 6b white 6f green 6g blue led cap: lens/insert colors jb clear/white jc clear/red jd clear/amber jf clear/green bright led led colors resistor no code no resistor 05 5-volt 12 12-volt 24 24-volt 5c red 5d amber 5f green w panel seal no code without panel seal w with panel seal (bushing mount only) spot illuminated cap: lens/insert colors ja clear/black jb clear/white jc clear/red je clear/yellow jf clear/green led for spot illuminated cap led colors forward voltage 02 2-volt (no resistor) 05 5-volt 12 12-volt 24 24-volt 1c red 1d amber 1f green 1cf red/green bicolor led for full face illuminated led colors forward voltage 02 2-volt (no resistor) 2cf red/green 05 5-volt 12 12-volt 24 24-volt led cap: lens/insert colors jb clear/white terminals 01 solder lug/.110 (2.8mm) quick connect * 03 straight pc * wire harness & cable assemblies offered only in americas important: switches are supplied without ul, culus & csa marking unless specifed. ul, culus & csa recognized only when ordered with marking on the switch. specifc models, ratings, & ordering in- structions are noted on general specif- cations page. www.nkk.com series yb short body pushbuttons www.nkk.com d103 d102 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt
series yb short body pushbuttons www.nkk.com d104 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles panel seal contact materials & ratings plunger position ( ) = momentary connected terminals throw & switch/lamp schematics pole model normal down normal down notes: switch is marked with nc, no, com, l+, lC. lamp circuit is isolated and requires external power source. sp yb15 *yb16 on on (on) on 1-3 1-2 spdt dp yb25 *yb26 on on (on) on 1-3 4-6 1-2 4-5 dpdt no code without panel seal w g w * when in latchdown position for the alternate circuit, cap position is .020 (0.5mm) above the built-in bezel. poles & circuits l (+) (-) l l (+) (-) l housing silver contacts gold contacts power level 3a @ 125/250v ac logic level 0.4va max. @ 28v ac/dc max. k black housing available in black only. the 1-piece body and bezel-barrier have a matte fnish. complete explanation of operating range in supplement section. with panel seal bushing mounting only bushing mounting snap-in mounting supplied with mounting nut and o-ring at089. supplied with mounting nut. s c round square r rectangular m n rectangular round k square bezel-barrier is an integral part of the switch body. shapes & mounting types 4 6 1 32 5 (com) 1 32 (com) bushing mounting snap-in mounting
series yb short body pushbuttons www.nkk.com d105 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt (15.0) sq .591 (12.2) .480 (4.0) .157 (21.0) .827 (12.2) .480 (4.0) .157 (15.0) .591 (15.0) dia .591 (12.2) .480 (4.0) .157 solder lug/ .110 (2.8mm) quick connect 01 03 terminals voltage v 5v ac 12v ac current i 115ma 60ma mscp .150 .150 endurance hours 7,000 average ambient temperature range C25c ~ +50c 05 12 t-1 bi-pin at611 incandescent lamp & solid cap electrical specifcations are determined at a basic temperature of 25c. lamp circuit is independent of switch operation. for dimension drawing of lamp see the accessories & hardware section. solid cap for incandescent lamp & nonilluminated lens/insert colors available: bb cb eb fb white/white blue/white green/white yellow/white red/white materials: lens & insert: polycarbonate seal/filter: thermoplastic elastomer straight pc (7.3) .288 epoxy seal (2.0) .079 (1.2) .047 (2.8) .110 thk = (0.5) .020 epoxy seal (0.6) r .024 (1.2) .047 (2.8) .110 (4.4) .173 thk = (0.5) .020 single pole double pole 1 4 2 5 63 c l (3.7) ty p .146 (4.85) ty p .191 (1.6) dia ty p .063 (5.55) ty p .219 (3.0) ty p .118 1 2 3 c l (3.7) ty p .146 (4.85) ty p .191 (1.6) dia ty p .063 (5.55) .219 (3.0) .118 at3001 square at3002 round at3003 rectangular translucent white insert translucent colored lens incandescent lamp at611 translucent white seal/filter gb no code no lamp
series yb short body pushbuttons www.nkk.com d106 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles (-) (+) (5.0) .197 (2.0) .079 (15.0) sq .591 (12.2) .480 (4.0) .157 (8.8) .346 (-) (+) (5.0) .197 (2.0) .079 (15.0) dia .591 (12.2) .480 (4.0) .157 (8.8) .346 (-) (+) (5.0) .197 (2.0) .079 (15.0) .591 (21.0) .827 (12.2) .480 (4.0) .157 (8.8) .346 spot illuminated cap with built-in led the electrical specifcations shown are determined at a basic temperature of 25c. led circuit is isolated and requires external power source. single color leds are colored in off state. bicolor led is translucent white in off state. if the source voltage exceeds the rated voltage, a ballast resistor is required. the resistor value can be calculated by using the formula in the supplement section. ja jb jc je jf without resistor with resistor with resistor with resistor unit forward peak current i fm 20 15 15 12 ma typical forward current i f 15 12.5 12.5 10 ma forward voltage v f 2.1 5 12 24 v reverse peak voltage (not applicable to bicolor) v rm 5 5 5 5 v current reduction rate above 25c ?i f 0.27 CCCC CCCC CCCC ma/c ambient temperature range C25 ~ +50 c 02 05 12 24 colors available: 1c 1d 1f 1cf red amber green red/green this spot-illuminated cap is factory assembled. lens/insert colors available: clear/black clear/green clear/yellow clear/red clear/white at3010 square at3011 round at3012 rectangular without resistor 2-volt with resistor 5, 12, 24-volt (+) (-) single color bicolor (+) (-) single color (+) (-) (+) (-) bicolor example part number when cap is ordered separate from switch: at3010f02ja for a square spot illuminated cap with green 2-volt led without resistor clear lens and black insert colored insert clear lens seal built-in led (integral part of the cap) materials: lens & insert: polycarbonate seal: thermoplastic elastomer
series yb short body pushbuttons www.nkk.com d107 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt bright led & led caps jb jc jd jf lens/insert colors available: clear/green clear/amber clear/red clear/white at3005 round transparent clear lens at634 5-volt, 2-element with resistor at634 12-volt, 4-element with resistor the electrical specifcations shown are determined at a basic temperature of 25c. led circuit is isolated and requires external power source. if the source voltage exceeds the rated voltage, a ballast resistor is required. the resistor value can be calculated by using the formula in the supplement section. electrical specifcations for bright led without resistor unit led colors red amber green forward peak current i fm 40 40 40 ma typical forward current i f 26 26 26 ma forward voltage v f 1.9 2.0 2.0 v reverse peak voltage v rm 4 4 4 v current reduction rate above 25c ?i f 0.50 ma/c ambient temperature range C25 ~ +50 c no code colors available: 5c 5d 5f red amber green no resistor (+) (-) bright at628 t-1 bi-pin translucent colored insert translucent white seal/diffuser bright leds at628 at634 cap for bright led electrical specifcations for bright led with resistor unit forward peak current i fm ma typical forward current i f 25 20 10 ma forward voltage v f 5 12 24 v reverse peak voltage v rm 4 8 16 v current reduction rate above 25c ?i f CCCC CCCC CCCC ma/c ambient temperature range C25 ~ +50 c colors available: 5c 5d 5f red amber green bright at634 t-1 1 ? 4 bi-pin 05 12 24 (-) (+) (+) (-) (+) (-) at634 24-volt, 4-element with resistor materials: lens & insert: polycarbonate seal/diffuser: thermoplastic elastomer (4.0) .157 (12.2) .480 (21.0) .827 (15.0) .591 at3006 rectangular (15.0) sq .591 (12.2) .480 (4.0) .157 (15.0) dia .591 (12.2) .480 (4.0) .157 at3004 square
series yb short body pushbuttons www.nkk.com d108 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles (15.0) sq .591 (12.2) .480 (4.0) .157 (4.0) .157 (12.2) .480 (21.0) .827 (15.0) .591 (15.0) dia .591 (12.2) .480 (4.0) .157 super bright led & led caps jb lens/insert colors available: clear/white at3014 square at3015 round at3016 rectangular cap for super bright led the electrical specifcations shown are determined at a basic temperature of 25c. led circuit is isolated and requires external power source. if the source voltage exceeds the rated voltage, a ballast resistor is required. the resistor value can be calculated by using the formula in the supplement section. transparent clear lens translucent white insert translucent white seal/diffuser super bright leds at625 at631 at632 electrical specifcations for super bright led forward peak current i fm 30 30 30 ma typical forward current i f 20 20 20 ma forward voltage v f 3.6 3.5 3.6 v reverse peak voltage v rm 5 5 5 v current reduction rate above 25c ?i f 0.50 ma/c ambient temperature range C25 ~ +50 c colors: super bright at625g blue at631b white at632f green t-1 bi-pin 6b 6f 6g unit white green blue (+) (-) a ttention electrostatic sensitive devices materials: lens & insert: polycarbonate seal/diffuser: thermoplastic elastomer
series yb short body pushbuttons www.nkk.com d109 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt (15.0) sq .591 (12.2) .480 (4.0) .157 (4.0) .157 (12.2) .480 (21.0) .827 (15.0) .591 (15.0) dia .591 (12.2) .480 (4.0) .157 electrical specifcations for bicolor led bicolor led is translucent white in off state. unit forward peak current i fm 60 60 20 12 ma typical forward current i f 45 45 15 10 ma forward voltage v f 2.1 5 12 24 v current reduction rate above 25c ?i f 0.80 CCCC CCCC CCCC ma/c ambient temperature range C25 ~ +50 c bicolor led & led caps 02 05 12 the electrical specifcations shown are determined at a basic temperature of 25c. led circuit is isolated and requires external power source. if the source voltage exceeds the rated voltage, a ballast resistor is required. the resistor value can be calculated by using the formula in the supplement section. jb 24 bicolor at621 2cf lens/insert colors available: clear/white at3004 square at3005 round at3006 rectangular t-1 1 ? 2 bi-pin red/green at621 bicolor led 5-volt 6-element with resistor at621 bicolor led 12 & 24-volt 6-element with resistor (+) (-) (+) (-) (+) (-) as shown for red; reverse polarity for green led caps transparent clear lens transparent white insert translucent white seal/diffuser bicolor led at621 materials: lens & insert: polycarbonate seal/diffuser: thermoplastic elastomer at621 bicolor led 2-volt 6-element without resistor
series yb short body pushbuttons www.nkk.com d110 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles (15.0) dia .591 (18.0) dia .709 (5.3) .209 (3.0) .118 (0.5) .020 (10.9) .429 (7.3) .288 (24.3) .957 (9.4) .370 m16 p1 (1.2) x (2.0) typ .047 x .079 (0.5) typ .020 (2.8) typ .110 latchdown position (0.5) .020 (9.7) .382 nc l - + n o no com 36 5 2 14 (6.0) .236 (11.1) .437 (3.7) .146 (15.0) sq .591 (18.0) sq .709 (10.9) .429 (7.3) .288 (24.3) .957 (9.4) .370 m16 p1 (1.2) x (2.0) ty p .047 x .079 (0.5) ty p .020 (8.3) .327 (2.8) ty p .110 (9.7) .382 nc l - + n o no com 36 5 2 14 (6.0) .236 (11.1) .437 (3.7) .146 typical switch dimensions square ? bushing mounting single & double pole rectangular ? snap-in mounting single & double pole round ? panel seal single & double pole yb15skw01-12-cb single pole models do not have terminals 4, 5, & 6. yb26wckw01-12-eb single pole models do not have terminals 4, 5, & 6. yb15nkw01-5c-jc single pole models do not have terminals 4, 5, & 6. panel thickness & cutouts bushing & panel seal mount snap-in mount (21.0) .827 (24.0) .945 (15.0) .591 (18.0) .709 (0.5) ty p .020 (2.8) ty p .110 (1.2) x (2.0) ty p .047 x .079 (8.3) .327 (7.3) .288 (24.3) .957 (9.7) .382 nc l - + n o no com 36 5 2 14 (6.0) .236 (11.1) .437 (3.7) .146 panel thickness .020 ~ .197 (0.5mm ~ 5.0mm) panel thickness .039 ~ .138 (1.0mm ~ 3.5mm) (16.0) .630 + 0.2 ? 0.0 dia (1.2) r .047 (16.0) .630 + 0.2 ? 0.0 dia
series yb short body pushbuttons www.nkk.com d111 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt (29.2) 1.150 (5.2) .205 (23.2) .913 (5.9) .232 (16.2) .638 (45.0) min* 1.772 (16.0) dia .630 (24.0) min .945 * minimum dimension allows opening of cover to 180 a t4175 (23.4) .921 (23.9) .941 (12.5) .492 180 optional accessories dust/splash cover protective guard at4072 protective guard opens 90 closes manually materials: lid: polycarbonate base: glass fiber reinforced polycarbonate spring loaded protective guard at4175 spring loaded protective guard opens 180 closes automatically materials: lid: polycarbonate base: glass fiber reinforced polyamide coil spring: stainless steel dust covers and protective guards reduce depth of switch behind panel by .047 (1.2mm). panel thickness range with dust cover or protective guards: bushing mounting .020 ~ .150 (0.5mm ~ 3.8mm) snap-in mounting .020 ~ .091 (0.5mm ~ 2.3mm) panel seal .020 ~ .118 (0.5mm ~ 3.0mm) (20.0) dia .787 (16.0) dia .630 (0.5) .020 (1.2) .047 (11.4) .449 assembled bezel height (23.9) .941 (23.4) .921 (12.0) .472 (16.0) dia .630 (1.2) .047 (6.6) .260 (11.2) .441 (1.2) .047 assembled cap height (23.9) .941 (22.9) .902 at 541 at 4115 a t089 at4115 dust cover for snap-in or bushing mount at4115 splash cover and at541 o-ring for bushing mount materials: lid: polyvinyl chloride base: polyamide o-ring: nitrile butadiene rubber dust cover splash cover note: at089 o-ring supplied with panel seal model. at541 at4115 snap-in mount panel seal a t4115 (12.5) .492 (16.0) dia .630
series yb short body pushbuttons www.nkk.com d112 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles assembly instructions grip slot projections to p view of switch switch body part number negative lamp socket positive lamp socket plunger pinhole (-) (+) spot flat (-) (+) flat (-) (+) led at628 at634 leds at625g at631b at632f led at621 spot illuminated cap with built-in led the following installation tools are available: at106 socket wrench for bushing mounting (overtightening the mounting nut at092 may damage the switch housing.); at109 cap extractor; at111 lamping tool. further details and dimensions are shown in the accessories and hardware section. cap assembly led polarity & orientation in lamp socket flat (+) (-) legends lens film insert filter seal cap base o n (15.0) sq .591 (13.48) sq .531 (0.76) ty p .030 (13.48) dia .531 (15.0) dia .591 (0.76) ty p .030 (21.0) .827 (19.48) .767 (0.76) ty p .030 (13.48) .531 (15.0) .591 (0.76) ty p .030 (12.2) sq .480 (10.68) sq .420 (0.76) ty p .030 (11.4) .449 (9.88) .389 (10.68) .420 (12.2) .480 (0.76) ty p .030 (0.76) ty p .030 (18.2) .717 (16.68) .657 (0.76) ty p .030 (10.68) .420 (12.2) .480 (0.76) ty p .030 o n shaded areas are printable areas. shaded areas are printable areas. recommended print method: laser print film insert: clear polyester, 4 mil max. thickness recommended methods: laser etch on clear lens, screen print or pad print on lens. epoxy based ink is recommended. nkk switches can provide custom legends for caps. contact factory for more information. a ttention electrostatic sensitive devices suggested printable area for yb lens suggested printable area for film insert

▲Up To Search▲

Price & Availability of YB15CKW01-6F-JB

	To Download YB15CKW01-6F-JB Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .